/*
 * OmniVision OV7620/OV7120 Camera Chip Support Code
 *
 * Copyright (c) 1999-2002 Mark McClelland <mark@alpha.dyndns.org>
 * http://alpha.dyndns.org/ov511/
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the
 * Free Software Foundation; either version 2 of the License, or (at your
 * option) any later version.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
 * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
 * for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software Foundation,
 * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 */

/* This file is not a module yet */
#define __NO_VERSION__

/* The kernel Makefile defines this when built with kernel */
#if defined(OUTSIDE_KERNEL)
	#if !defined(EXPORT_SYMTAB)
		#define EXPORT_SYMTAB
	#endif

	#include <linux/config.h>

	#if defined(CONFIG_MODVERSIONS) && !defined(MODVERSIONS)
		#define MODVERSIONS
	#endif

	#include <linux/version.h>

	#ifdef MODVERSIONS
		#include <linux/modversions.h>
	#endif
#else
	#include <linux/config.h>
	#include <linux/version.h>
#endif

#include <linux/slab.h>
#include "ov511.h"

/* These may not be correct!! They are only here to make the code compile. */
#define REG_GAIN		0x00	/* gain setting (5:0) */
#define REG_BLUE		0x01	/* blue channel balance */
#define REG_RED			0x02	/* red channel balance */
#define REG_SAT			0x03	/* saturation */
					/* 04 reserved */
#define REG_CNT			0x05	/* Y contrast */
#define REG_BRT			0x06	/* Y brightness */
					/* 08-0b reserved */
#define REG_BLUE_BIAS		0x0C	/* blue channel bias (5:0) */
#define REG_RED_BIAS		0x0D	/* read channel bias (5:0) */
#define REG_GAMMA_COEFF		0x0E	/* gamma settings */
#define REG_WB_RANGE		0x0F	/* AEC/ALC/S-AWB settings */
#define REG_EXP			0x10	/* manual exposure setting */

extern int debug;	/* Exists in ov511.c and ov518.c */

struct ov7x20 {
	struct ov_i2c *i2c;
	int auto_brt;
	int auto_exp;
	int backlight;
	int bandfilt;
	int mirror;
};

static struct ovsensor_regvals regvalsNorm7x20[] = {
	{ 0x00, 0x00 },
	{ 0x01, 0x80 },
	{ 0x02, 0x80 },
	{ 0x03, 0xc0 },
	{ 0x06, 0x60 },
	{ 0x07, 0x00 },
	{ 0x0c, 0x24 },
	{ 0x0c, 0x24 },
	{ 0x0d, 0x24 },
	{ 0x11, 0x01 },
	{ 0x12, 0x24 },
	{ 0x13, 0x01 },
	{ 0x14, 0x84 },
	{ 0x15, 0x01 },
	{ 0x16, 0x03 },
	{ 0x17, 0x2f },
	{ 0x18, 0xcf },
	{ 0x19, 0x06 },
	{ 0x1a, 0xf5 },
	{ 0x1b, 0x00 },
	{ 0x20, 0x18 },
	{ 0x21, 0x80 },
	{ 0x22, 0x80 },
	{ 0x23, 0x00 },
	{ 0x26, 0xa2 },
	{ 0x27, 0xea },
	{ 0x28, 0x20 },
	{ 0x29, 0x00 },
	{ 0x2a, 0x10 },
	{ 0x2b, 0x00 },
	{ 0x2c, 0x88 },
	{ 0x2d, 0x91 },
	{ 0x2e, 0x80 },
	{ 0x2f, 0x44 },
	{ 0x60, 0x27 },
	{ 0x61, 0x02 },
	{ 0x62, 0x5f },
	{ 0x63, 0xd5 },
	{ 0x64, 0x57 },
	{ 0x65, 0x83 },
	{ 0x66, 0x55 },
	{ 0x67, 0x92 },
	{ 0x68, 0xcf },
	{ 0x69, 0x76 },
	{ 0x6a, 0x22 },
	{ 0x6b, 0x00 },
	{ 0x6c, 0x02 },
	{ 0x6d, 0x44 },
	{ 0x6e, 0x80 },
	{ 0x6f, 0x1d },
	{ 0x70, 0x8b },
	{ 0x71, 0x00 },
	{ 0x72, 0x14 },
	{ 0x73, 0x54 },
	{ 0x74, 0x00 },
	{ 0x75, 0x8e },
	{ 0x76, 0x00 },
	{ 0x77, 0xff },
	{ 0x78, 0x80 },
	{ 0x79, 0x80 },
	{ 0x7a, 0x80 },
	{ 0x7b, 0xe2 },
	{ 0x7c, 0x00 },
	{ 0xff, 0xff },	/* END MARKER */
};

/* This initializes the OV7x20 sensor and relevant variables. */
static int
ov7x20_configure(struct usb_ov511 *ov)
{
	struct ov7x20 *s;
	int rc;

	PDEBUG(4, "entered");

	ov->spriv = s = kmalloc(sizeof *s, GFP_KERNEL);
	if (!s)
		return -ENOMEM;
	memset(s, 0, sizeof *s);

	s->i2c = ov->i2c;
	s->auto_brt = 1;
	s->auto_exp = 1;

	/* Set sensor-specific vars */
	ov->maxwidth = 640;
	ov->maxheight = 480;
	ov->minwidth = 64;
	ov->minheight = 48;

	rc = ovsensor_write_regvals(ov, regvalsNorm7x20);

	return rc;
}

static int
ov7x20_set_control(struct usb_ov511 *ov, struct ovsensor_control *ctl)
{
	struct ov7x20 *s = ov->spriv;
	struct ov_i2c *i2c = s->i2c;
	int rc;
	int v = ctl->value;

	switch (ctl->id) {
	case OVSENSOR_CID_CONT:
	{
		unsigned char ctab[] = {
			0x01, 0x05, 0x09, 0x11, 0x15, 0x35, 0x37, 0x57,
			0x5b, 0xa5, 0xa7, 0xc7, 0xc9, 0xcf, 0xef, 0xff
		};

		/* Use Y gamma control instead. Bit 0 enables it. */
		rc = i2c->w(ov, 0x64, ctab[v >> 12]);
		break;
	}
	case OVSENSOR_CID_BRIGHT:
		/* 7620 doesn't like manual changes when in auto mode */
		if (!s->auto_brt)
			rc = i2c->w(ov, REG_BRT, v >> 8);
		else
			rc = 0;
		break;
	case OVSENSOR_CID_SAT:
		rc = i2c->w(ov, REG_SAT, v >> 8);
		break;
	case OVSENSOR_CID_EXP:
		rc = i2c->w(ov, REG_EXP, v);
		break;
	case OVSENSOR_CID_FREQ:
	{
		int sixty = (v == 60);

		rc = i2c->w_mask(ov, 0x2a, sixty?0x00:0x80, 0x80);
		if (rc < 0)
			goto out;

		rc = i2c->w(ov, 0x2b, sixty?0x00:0xac);
		if (rc < 0)
			goto out;

		rc = i2c->w_mask(ov, 0x76, 0x01, 0x01);
		break;
	}
	case OVSENSOR_CID_BANDFILT:
		rc = i2c->w_mask(ov, 0x2d, v?0x04:0x00, 0x04);
		s->bandfilt = v;
		break;
	case OVSENSOR_CID_AUTOBRIGHT:
		rc = i2c->w_mask(ov, 0x2d, v?0x10:0x00, 0x10);
		s->auto_brt = v;
		break;
	case OVSENSOR_CID_AUTOEXP:
		rc = i2c->w_mask(ov, 0x13, v?0x01:0x00, 0x01);
		s->auto_exp = v;
		break;
	case OVSENSOR_CID_BACKLIGHT:
	{
		rc = i2c->w_mask(ov, 0x68, v?0xe0:0xc0, 0xe0);
		if (rc < 0)
			goto out;

		rc = i2c->w_mask(ov, 0x29, v?0x08:0x00, 0x08);
		if (rc < 0)
			goto out;

		rc = i2c->w_mask(ov, 0x28, v?0x02:0x00, 0x02);
		s->backlight = v;
		break;
	}
	case OVSENSOR_CID_MIRROR:
		rc = i2c->w_mask(ov, 0x12, v?0x40:0x00, 0x40);
		s->mirror = v;
		break;
	default:
		PDEBUG(2, "control not supported: %d", ctl->id);
		return -EPERM;
	}

out:
	PDEBUG(3, "id=%d, arg=%d, rc=%d", ctl->id, v, rc);
	return rc;
}

static int
ov7x20_get_control(struct usb_ov511 *ov, struct ovsensor_control *ctl)
{
	struct ov7x20 *s = ov->spriv;
	struct ov_i2c *i2c = s->i2c;
	int rc = 0;
	unsigned char val = 0;

	switch (ctl->id) {
	case OVSENSOR_CID_CONT:
		rc = i2c->r(ov, 0x64, &val);
		ctl->value = (val & 0xfe) << 8;
		break;
	case OVSENSOR_CID_BRIGHT:
		rc = i2c->r(ov, REG_BRT, &val);
		ctl->value = val << 8;
		break;
	case OVSENSOR_CID_SAT:
		rc = i2c->r(ov, REG_SAT, &val);
		ctl->value = val << 8;
		break;
	case OVSENSOR_CID_EXP:
		rc = i2c->r(ov, REG_EXP, &val);
		ctl->value = val;
		break;
	case OVSENSOR_CID_BANDFILT:
		ctl->value = s->bandfilt;
		break;
	case OVSENSOR_CID_AUTOBRIGHT:
		ctl->value = s->auto_brt;
		break;
	case OVSENSOR_CID_AUTOEXP:
		ctl->value = s->auto_exp;
		break;
	case OVSENSOR_CID_BACKLIGHT:
		ctl->value = s->backlight;
		break;
	case OVSENSOR_CID_MIRROR:
		ctl->value = s->mirror;
		break;
	default:
		PDEBUG(2, "control not supported: %d", ctl->id);
		return -EPERM;
	}

	PDEBUG(3, "id=%d, arg=%d, rc=%d", ctl->id, ctl->value, rc);
	return rc;
}

static int
ov7x20_command(struct usb_ov511 *ov, unsigned int cmd, void *arg)
{
	switch (cmd) {
	case OVSENSOR_CMD_S_CTRL:
		return ov7x20_set_control(ov, arg);
	case OVSENSOR_CMD_G_CTRL:
		return ov7x20_get_control(ov, arg);
	default:
		PDEBUG(2, "command not supported: %d", cmd);
		return -ENOIOCTLCMD;
	}
}

struct ovsensor_ops ov7x20_ops = {
	configure:	ov7x20_configure,
	command:	ov7x20_command,
};